thinkpads.com Support Community Forum Index Bill Morrow's thinkpads.com Open Forum - The Original Thinkpad Support Forum
Follow ThinkpadsForum on Twitter
 Support this forum, shop at newmodeus.com
  Support the forum, shop at newmodeus.com
Our oldest longest advertiser of parts for ThinkPads
Goodbye Lorita, wherever you've gone..

If you've found this forum useful, please consider donating a dollar or two

It is currently Sat Jul 04, 2015 7:13 pm

All times are UTC-05:00




Post new topic  Reply to topic  [ 6 posts ] 
Author Message
PostPosted: Sat Apr 28, 2012 3:10 pm 
Offline
Sophomore Member

Joined: Sat Apr 28, 2012 2:53 pm
Posts: 127
Location: Aberdeen
Evening All!!! First time poster but long time follower and I'm needing a wee bit of help!

Basically I've been dragged kicking and screaming into helping out a mate of mine with a ThinkPad R500 (MPN: 2716-W7F) that he purchased off of eBay UK for £74.00p (roughly US $120.00) - it was purchased as spares & repairs but all it needed done to get it working was to reseat the single DIMM that was present (lucky git I say! :eek: ).

Unfortunately that was the easy bit to the story - the palmrest has a big old crack in it (still usable but the cracked edges are sharp) but also the optical drive eject arm is basically loose i.e. it sticks out fully and can be easy pushed back in but just pops out by itself.

Basically what I need to confirm is how easy is it to get the optical drive eject arm fixed (i.e. is it a spring that's gone inside that mechanism?) and how much disassembly is needed to get at it - next with regards to the palmrest, I have spare one from a 15.4" T61p (FRU: 42W2024) and just wanted to see would that be compatible for use with the R500; the latter I'm not to sure about as I can't see the FRU listed within the service manual but wasn't sure if the basic level of support was present (i.e. FrankenPad level).

Thanks in advance and appreciate any assistance & input you can provide me.

Cheers, Scotty Boy! :D


Top
   
PostPosted: Thu May 17, 2012 7:11 pm 
Offline
Sophomore Member

Joined: Fri Sep 24, 2010 10:52 pm
Posts: 194
Location: Canada
I'm not sure about the ejector arm, but the palm rest is very easy to replace. I think it is held by a few screws that you can acess from the bottom of the laptop. If you reseated the DIMM you should know how to remove the palmrest. For the ejector arm I would download the maintenance manual and take a look.

_________________
I'M DONE WITH THINKPADS, JUST DONE!!!


Top
   
PostPosted: Mon May 28, 2012 8:43 am 
Offline
Sophomore Member

Joined: Sat Apr 28, 2012 2:53 pm
Posts: 127
Location: Aberdeen
sir_synthsalot wrote:
I'm not sure about the ejector arm, but the palm rest is very easy to replace. I think it is held by a few screws that you can acess from the bottom of the laptop. If you reseated the DIMM you should know how to remove the palmrest. For the ejector arm I would download the maintenance manual and take a look.


Thanks for your reply post - replacing the palmrest is easy but I was asking about confirming the compatibility of an older model palmrest (T61/R61 series) with the R500 ThinkPad; I've confirmed that the one I have is not compatible and have purchased a replacement for it to get that addressed for my mate.

With regards to the ejector arm I've confirmed that it's built into the frame and would require the bottom section of the case and frame to be replaced, so the decision has been made to leave that as is for the time being as the prices listed on eBay UK along with local resellers is quite high.


Top
   
PostPosted: Wed May 30, 2012 4:04 pm 
Offline
Moderator
Moderator

Joined: Sun Jan 01, 2006 3:29 pm
Posts: 2905
Location: San Francisco, CA
Palmrest is not compatible with T61. The ejector arm problem can be many things, ranging from no parts needed up to needing a base. It needs to be disassembled to examine. It requires removing the motherboard and frame. Sometimes the ejector arm can be snapped back into its track.


Top
   
PostPosted: Tue Jul 09, 2013 1:48 am 
Offline
ThinkPadder
ThinkPadder

Joined: Thu Sep 22, 2011 2:41 pm
Posts: 1812
Location: Hockessin, Delaware
You can usually replace the ejector parts if they are damaged. I have a few sets for T61, but don't have a disassembled R500 to compare if they are the same. If you remove the lower cover you should be able to tell what's broken.


Top
   
PostPosted: Fri Sep 26, 2014 10:40 am 
Offline
Sophomore Member

Joined: Sat Apr 28, 2012 2:53 pm
Posts: 127
Location: Aberdeen
Update: The 'ejector arm' was swapped out from the base unit of an archived T61p 15.4" WS - thankfully it fit in perfectly without any issues, which was a very welcome & pleasant surprise.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 6 posts ] 

All times are UTC-05:00


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited