thinkpads.com Support Community Forum Index Bill Morrow's thinkpads.com Open Forum - The Original Thinkpad Support Forum
Follow ThinkpadsForum on Twitter
 Support this forum, shop at newmodeus.com
 Support the forum, shop at newmodeus.com
IBM & lenovo legacy model ThinkPad support files are available on thinkpads.com.
including Hardware Maintenance Manuals, latest or final driver updates and more.

If you so wish:
Donate using PayPal

It is currently Wed Sep 17, 2014 12:29 am

All times are UTC - 5 hours




Post new topic Reply to topic  [ 3 posts ] 
Author Message
PostPosted: Thu Jan 26, 2012 12:41 pm 
Offline

Joined: Wed Jan 18, 2012 12:45 pm
Posts: 2
Hi there,
I am having a problem with my (formerly) trusty X32 display, and having been through the forum still cannot shed light on the problem.
All is OK on an external Monitor.
On start-up the screen flashes up at full intensity for about a second, dims to about half intensity for another second then dims completely. The image is still just about visible, so it looks to be the CCFL backlight that is not staying powered up.

The fact that the screen is at full intensity initially (even though momentarily) suggests to me that the backlight is physically OK.

I have replaced the inverter (makes no difference) and checked all the connections that I can get to (have had the LCD panel out to do this) - and still the same problem.
I did notice when changing the inverter that the screen would occasionally flash to full intensity when the inverter was moved about, but it would never stay on.

I now see that the micro-switch that is operated by the lid close switch has come off the board completely - and so I am wondering if that is somehow critical to the power circuit (I can live without the lid dimming the screen when closed).

Any ideas of what to check next gratefully received


Top
 Profile  
 
PostPosted: Thu Jan 26, 2012 5:28 pm 
Offline
RBS10000
RBS10000

Joined: Mon Sep 18, 2006 5:17 am
Posts: 13479
Location: Mt. Cobb, PA USA
That switch is Normally Closed (the little pin is in UP position), meaning it lets current pass through the switch.
If you press on the little pin the CCFL goes out.
Same thing if you remove the switch, the CCFL goes out.
Check where the switch was, and solder a tiny jumper wire across the old switch contacts.
When done, put some Kapton tape over it. If you don't have that, electrician's tape will do also.
Problem solved.

_________________
Lovely day for a Guinness! (The Real Black Stuff)

Check out The Board Room for:
- LED-mods for the 15" T60/R60/R61
- SATA-mods for any T43/R52 with ATI GPU
- other Services


Top
 Profile  
 
PostPosted: Thu Jan 26, 2012 5:39 pm 
Offline

Joined: Wed Jan 18, 2012 12:45 pm
Posts: 2
Thanks for the info and have had a crack at it. But with no great success

There are three contacts underneath where the switch was seated. (Two on one side of the hole it sits in and one the other).

While testing to make sure I was connecting the right contacts (by holding the jumper across the contacts) the best I could get was for the screen to flash on again - I could not get the screen to stay lit up for more than a second.
So I do not know which contacts to connect, and am not convinced it will work.


I haven't got as far as taking out the board and checking if all is OK underneath - is this the next step ?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group